Home > Not Working > Some Hot Tub Jets Not Working

Some Hot Tub Jets Not Working

Contents

I can't beleive two pumps would fail the exact same way at the same time. They don't run, hum, get warm….nothing. Apologies if this is already written up somewhere or misplaced. Solution: Check the connection or replace the sensor. http://elliottwaveresearch.com/not-working/bmw-e61-key-fob-not-working.html

Please enter a valid e-mail address We're sorry. Usually a large knob or dial will allow a spa user to open and close jets while seated inside of the spa. You're so thorough at draining your spa that you evacuate every elbow, every little 1/2" line, and every piece of equipment until you know there's not a drop of moisture in With the lid off, turn the spa on with the pump on low (do not hit the 'jets' button). http://www.troublefreepool.com/threads/9426-Jets-not-working-after-fresh-fill

Some Hot Tub Jets Not Working

If your motor looks like this, get a new pump assembly (don't let the shaft seal leak for long or this is what your pump will look like). If that does not work, the problem is in the circuit board itself. It has high and low speed. DO NOT DISCONNECT IT COMPLETELY.

After bleeding, try turning the power on again and see if the jets work. Please Confirm you are not a bot Spa Community Hot Tub Toolbox Hot Tub Information How-to Videos Blog Come Soak With Us: Rave On Actual UnsolicitedCustomer Feedback No question just want You should hear air or see water coming from it once it's loose. Hot Tub Jets Weak You can test it with an old style dial multimeter or you can just try a new one.

To check your impeller, shut off power and close valves on both sides of the pump. If the cable is good try a new panel. Got it? https://aqua-tech.ca/support-posts/the-pump-on-my-hot-tub-works-but-the-jets-dont-turn-on/ I believe its early to mid 90's.

I ran it without filter and it ran for hours no problem. In Ground Spa Jets Not Working Air Leak in Front of Pump? Could it be debri? If the pump is coming on but not pumping water, then it has an air lock.

  1. I see that power is coming to the main circuit board.
  2. Do not use the lock ring for this, just the lid.
  3. And when the spa pump ain't happy, ain't nobody happy - that's because without water flow, there is no filtration, no sanitation and no heating.
  4. Would a bad pressure switch do it?
  5. He moved and we were happy to get it from the new owner.

Half Of Hot Tub Jets Not Working

You've got a tub full of water but you've got a lot of plumbing with a lot of air bubbles trapped inside.

Find your filter. Some Hot Tub Jets Not Working Which can occur if you just drained the hot tub. Hot Tub Air Lock Symptoms Home Pool School Forum FAQ Forum Actions Mark Forums Read Quick Links View Site Leaders PoolMath Rules What's New?

Reply With Quote 05-21-2015,11:14 PM #11 lanecass View Profile View Forum Posts View Articles Join Date May 2015 Location caldwell tx Posts 2 Re: Jets not working after fresh fill? his comment is here If the pump is on low, it won't be a disaster, just a little wet. a perfectly working hot tub again! You're so thorough at draining your spa that you evacuate every elbow, every little 1/2" line, and every piece of equipment until you know there's not a drop of moisture in Hot Tub Jets Won't Turn On

Nothing happened.Jet1 works great...lots of action on that side of the tubJet2...nothing on the other side.The troubleshooting guide says to take off the door, and play with the pump.Typically, I would Clogged Drain Cover? PLEASE NOTE: Wet ends vary. http://elliottwaveresearch.com/not-working/css-top-not-working.html Can you access the equipment?

The wiring and equipment described in this article represent a typical spa pack. Bathtub Jets Not Working Low Water Level in Spa? This is probably time to break out your Yellow Pages and call a spa tech.

Its very odd.

Some of the older Beachcomber models had a piggyback set of filters stacked on top of each other with a draw string to reach the lower filter. DO NOT DISCONNECT IT COMPLETELY. Look for tiny bleed screws on the end of the pump. Hot Tub Pump Not Working If that doesn't work you likely have a bad motor.

The pump sounds fine, but there's no water moving. Second, if your tub is full, and still no water runs out, look for any closed valves before or after the pump. Swimming Pool Steve 3,310 views 1:27 How to Diagnose Your Hot Tub Pressure Switch for Flow Problems | Arctic Spas - Duration: 3:41. navigate here Normally only for about ten seconds or so, then tighten it back up and try the pump again.Yes, shut the power off, but you only need to slightly loosen it to

If not, you may have to use the drain plug or keep reading. Remove it for a few minutes from the spa and see if the jet action improves on hi speed with no filter. If you didn't just drain your tub and you don't think you have an air lock, try the following: 1) Is the high speed pump working? thanks for the information!

Of course, you'd never have gotten yourself into this situation if you'd just closed the valves on either side of the equipment before you drained it. If the plunger gets stuck on the hole, turn the spa off and remove it.