Home > Dodge Ram > Dodge Ram Trailer Lights Not Working

Dodge Ram Trailer Lights Not Working

Contents

Acknowledgements: Diagram: offroaders.com Chart: Turbo Diesel Register Write-up by Joe Leonard, MoparTruckParts.com For more information about Dodge truck wiring click the link below: Ram Trailer Connector Wiring Link Joe Leonard 2009-12-6 I have the factory installed harness that comes back from the underhood fuse blocks. Wiring kits that include these items are available. The trailer brake and turn circuits come from relays in the power distribution center. navigate here

Contact Us - RamForum.com - Archive - Top Powered by vBulletin Version 3.8.7Copyright ©2000 - 2016, vBulletin Solutions, Inc. Testing the vehicle without the trailer will allow you to separate the wiring system into manageable sections. The connector on the vehicle should have a ground wire connected to a clean bare metal surface on the frame. 2. yes. http://www.justanswer.com/dodge/54c6f-dodge-ram-1500-trailer-wiring-not-working-properly-tried.html

Dodge Ram Trailer Lights Not Working

Determine amperage draw of trailer lights and confirm that lights do not draw more power than the harness can handle. I'll keep the thread going until I can figure this out. 05 Durango SLT 4.7 265/70/17 Grabber AT2 TB lift Superchips 91 tune True Flow sealed intake Last edited by BlueSLT05; Corrosion will usually be green or white in color. I checked both sides of that plug and I get a flashing test light from the white/pink wire when the right turn signal is on.

  • See if one, two, or no terminals light up.
  • Each component should have its own ground for the best performance (Figure 6).
  • And you are correct there seems to be a fuse for each circuit!..
  • Share Share this post on Digg Del.icio.us Technorati Twitter __________________ 2014 express quad cab (sold) 2010 crew cab lone star.

Unplug it and plug it back in with the headlights still on. Relay is clicking. In addition, you will want to have basic wiring tools on hand. Trailer Running Lights Not Working But Brake Lights Do Check the bulb in any light not working and make sure it isn't burned out.

If there is a weak ground, when you apply the brakes with the taillights on is when the problem will show up. Repair or replace any damaged wire sections (Figure 7). Yesterday 06:52 PM by Howitzer69 3 I dropped my truck and... http://www.dodgetalk.com/forums/showthread.php?t=356752 Expert: sprinkles08 replied5 years ago.

I unhooked it thinking it may be the culprit, called my local dealer and asked about the relay with no luck- they said they would have to sell me the whole 2014 Dodge Ram Trailer Running Lights Not Working The Grafx Shop 78,245 views 14:03 Dodge TIPM low beam repair. - Duration: 3:24. Published on Sep 13, 2014This is how to change the trailer light relays that are inside the fuse box. For example: Left taillight not flashing on the trailer when it is flashing on the truck, or clearance lights flickering on the trailer.

2014 Dodge Ram Trailer Lights Not Working

adventureoflinkmk2 185,832 views 8:38 2014 Ram Brake Controller Factory Type Install How To - Duration: 22:49. Harness wires are not connected to vehicle correctly/securely. (Plug-In Only) A set of connectors is not seated together properly or is not making a good connection. (Plug-In Only) A required fuse Dodge Ram Trailer Lights Not Working If damaged, replace the bulb or light assembly as needed. Trailer Running Lights Not Working Insufficient ground or short to ground on trailer.

Connect 12V power wire directly to vehicle battery. http://elliottwaveresearch.com/dodge-ram/2004-dodge-ram-interior-lights-not-working.html Mark helpful 100,305 Report dandyoun answered 2 years ago Are your truck lights working normally with trailer hooked up and not hooked up? 2 out of 2 people think this is On the Trailer Make sure that the ground wire (usually white) on the trailer connector is securely attached to the trailer frame. Use a wiring diagram to check that the correct wires are tapped into. Dodge Ram Trailer Running Light Fuse

Register Now In order to be able to use most of our features, you must first register. I checked all the fuses I could find. Yellow wiring goes to the driver's side. http://elliottwaveresearch.com/dodge-ram/dodge-ram-tail-lights-not-working.html Where to Begin When it comes to troubleshooting a wiring installation, testing is everything.

AOL E-MAIL USERS: Please click HERE for important info pertaining to your e-mail address. 2011 Dodge Ram Trailer Running Lights Fuse WEAK GROUND ISSUES If some of the lights work, but not all of them, you may have a ground problem. briansmobile1 48,674 views 22:49 How to: Change TIPM ( Totally Integrated Power Module) - Duration: 14:03.

Mark helpful 50 Report tiredofnotgettingtofish answered 2 years ago Your right, it ended up the trailer ground was not a good enough connection, I"m now makeshifting a better connection so that

Make sure your meter has a fresh battery and unbroken leads with sharp points. I have checked the fuse block and everything there seems to be OK. Also, I did this test with the truck running and not running (in case that matters). 2003 Dodge Ram Trailer Lights Not Working My guess is factory looking at the wiring.

Consult our T-One Fit Guide for more information. Check the trailer and vehicle plugs for corrosion. I would expect to get a constant 12V...like I do for the left signal. http://elliottwaveresearch.com/dodge-ram/2004-dodge-ram-backup-lights-not-working.html Ask Your Own Dodge Question Customer: replied5 years ago.

What's going on? 2 answers Recently replaced my battery, due to loose terminal post, also connected a cut hot wire going to ac plug that apparently powers the ac sensor. Today 01:56 AM by Shawner 4 New to the 1st gens Today 01:16 AM by Sniper X 35 What happened to D.T. Yesterday 10:46 PM by ScarredKnightfn 2 2 Attachment(s) New to me 1974 D200 Yesterday 10:43 PM by ScarredKnightfn 385 554 Attachment(s) Do you use the... I tried Resolved Question: Trailer wiring is not working properly.